Hosted by Nordic Semiconductor Date and time Thu, 04 October 2018, 18:00 - 21:30
Venue Cocoon Networks, 4 Christopher St, London, EC2A 2BS
Limited to 30 participants
How to participate You must apply to participate. If you are selected you will receive an email confirmation after the 20.09.2018. This will include the link to book your free ticket (a non-refundable booking fee of £15 will be charged to limit drop-outs).
Drinks and pizza will be served throughout the night.
Limited to 30 participants
How to participate You must apply to participate. If you are selected you will receive an email confirmation after the 20.09.2018. This will include the link to book your free ticket (a non-refundable booking fee of £15 will be charged to limit drop-outs).
Food and drinks will be served throughout the event
bonus for participants
- Free nRF52840-DK. - Free nRF52840 dongle kit (only if participants contact Nordic within two weeks of the workshop with project details).
Hardware Pioneers has teamed up with Nordic Semiconductor again to show you how to use the newly released nRF Mesh mobile app for mesh setup and configuration, and how to expand upon the examples in the mesh SDK to add user defined behaviour.
The nRF Mesh apps enables you to provision, configure and control Bluetooth mesh networks. They demonstrate a subset of the capabilities of the nRF Mesh open source libraries. Nordic has created these apps to bring the natural benefits of using a smart phone in Bluetooth mesh setup and control activities. Provision in devices with authentication and use the generic interface to configure the nodes. Use source code on GitHub as a starting point for your Bluetooth mesh development. Source code for iOS available here and Android available here.
The nRF52 Series re-defines the world of possibilities for Bluetooth® low energy sensors and devices for the IoT era
What you'll learn
Understanding the basic software development in Segger Embedded Studio.
Using the nRF Mesh app for Android/iOS.
Using the nRF SDK for Mesh.
Extending the basic mesh examples to add user defined behaviour (sensor readout, servo control).
Who is this workshop for?
[job role]
[job role]
[job role]
[job role]
This workshop is for anyone who wants to learn more about an introduction to Bluetooth (mesh in particular), and/or how to develop software for the Nordic nRF52 series of RF SoC’s.
Requirements
Equipment
How to setup and deploy templates to setup and
deploy templates and sensors on Intel Edison to setup
and deploy templates.
How to setup and deploy templates to setup and
deploy templates and sensors on Intel Edison to setup
and deploy templates.
downloads
How to setup and deploy templates to setup and
deploy templates and sensors on Intel Edison to setup
and deploy templates. How to setup and deploy templates to setup and deploy templates and sensors on Intel Edison to setup and deploy templates.
Submit your question to the experts (optional) Is there any particular topic you would like to cover during the event? Or a question you’d like our panel of experts to answer?
8.00pm Community announcements and demos: This is your time. If you would like to share what
you are working on with the community or make any sort of announcement. You have 2
minutes max for a short shoutout.
9.00pm Networking and drinks.
9.30pm Event ends.
Requirements
Equipment
- Your own laptop. - Micro USB cable (type B, same as used on older Android phones). - Basic C programming. - Go through the Getting Started section of the nRF SDK for Mesh documentation. * Important note: Complete the first two chapters of the Getting Started section: - Installing the toolchain. - Building the mesh stack and examples.
How to setup and deploy templates to setup and
deploy templates and sensors on Intel Edison to setup
and deploy templates.
How to setup and deploy templates to setup and
deploy templates and sensors on Intel Edison to setup
and deploy templates.
Submit your question to the experts (optional) Is there any particular topic you would like to cover during the event? Or a question you’d like our panel of experts to answer?
Torbjørn Øvrebekk, Sr. Application Engineer at Nordic Semiconductor 10 years of experience in Nordic working both as an apps engineer in the support group and as a field applications engineer in the US. Torbjørn handles mostly software and RF protocol related support, as well as attending trade shows and doing technical presentations.
Bjørn Kvaale, Application Engineer at Nordic Semiconductor Coming soon.
[Instructor Full Name], [Job Role] at [Company Name] [Instructor bio].
About the platform and the hosting company
About the nRF5 SDK for Mesh The nRF5 SDK for Mesh is Nordic Semiconductor's implementation of the Bluetooth Mesh. It allows applications to utilize the features provided by the Bluetooth Mesh when running on Nordic's nRF5 Series chips.
About the nRF52 Series The nRF52 series is the latest short range wireless SoC from Nordic. Based on the ARM Cortex M4 MCU, and with a host of analog and digital interfaces, these devices form a good starting point for low power, single chip RF applications.
About Nordic Semiconductor Nordic Semiconductor is the #1 provider of low power wireless solutions with a sustained market share of more than 40% in Bluetooth® Low Energy chipsets. The company is headquartered in Norway, and has a global footprint in IoT solutions based on several technologies also including ANT, IEEE 802.15.4, Thread, Zigbee and 2.4GHz proprietary. Nordic is also getting ready to launch a new product line based on LTE-M and NB-IoT technologies.
About [Company name] [Company info].
When and where
Date and time
Thu 04 October 2018 18:00 - 21:30
Venue
Cocoon Networks, 4 Christopher Street, London, EC2A 2BS
.gif)
-29.png){kind=small}